‹W4A33›

User Tools

Site Tools

You are here: start » intakemanifold
Trace:
morrisonfabrications
intakemanifold

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
intakemanifold [2020/05/16 08:52] – adminintakemanifold [2020/05/17 18:27] (current) – admin
Line 30: Line 30:
 ===Turbo Cyclone split runner=== ===Turbo Cyclone split runner===
 This intake manifold is basically the Evo3 intake manifold for large runner heads. It has two separate sets of intake runners. One set is longer then the other and they feed into a single port at the cylinder head and have a divider much like you see in a cylinder head. It has an actuated set of butterflies in a set of runners. The way it works is off boost the butterflies stay closed and that keeps the air moving through one set of runners and keeps manifold air high velocity and this helps increase off boost throttle response and spool. Then once boost pressure comes on the butterflies go open to take advantage of the large volume to make horsepower.  There are several ways to actuate this. You can do it the stock way, use a electronic device to work it or you can do a mechanical setup with an internal wastegate actuator. Be aware that there are stock manifolds out there that arent split runner that say Cyclone. Those are different then these 3 piece split runner cyclones. The top end powerband is slightly better then stock but not much. This manifold is good for about 7800-8000 RPM or higher depending on camshaft. This intake manifold is basically the Evo3 intake manifold for large runner heads. It has two separate sets of intake runners. One set is longer then the other and they feed into a single port at the cylinder head and have a divider much like you see in a cylinder head. It has an actuated set of butterflies in a set of runners. The way it works is off boost the butterflies stay closed and that keeps the air moving through one set of runners and keeps manifold air high velocity and this helps increase off boost throttle response and spool. Then once boost pressure comes on the butterflies go open to take advantage of the large volume to make horsepower.  There are several ways to actuate this. You can do it the stock way, use a electronic device to work it or you can do a mechanical setup with an internal wastegate actuator. Be aware that there are stock manifolds out there that arent split runner that say Cyclone. Those are different then these 3 piece split runner cyclones. The top end powerband is slightly better then stock but not much. This manifold is good for about 7800-8000 RPM or higher depending on camshaft.
 +{{ http://w4a33.com/images/turbocyclone.jpg?467x350 }}
 ===N/A Cyclone Split runner=== ===N/A Cyclone Split runner===
 The function of this manifold is the same as the Cyclone except it is a two piece design instead of a 3 peice. It does not say Cyclone on the casting. This manifold is found in EDM Galant Dynamic-4, Galant AMG, JDM/EDM Galant GTi. They are rare items and also have actuated butterflies and split runners. These intake manifolds have a far smoother design with better shaped runners and a larger plenum volume. The top end powerband is a good bit better then the Turbo Cyclone but not much. This manifold is good for about 8000-9000 RPM or higher depending on camshaft. The function of this manifold is the same as the Cyclone except it is a two piece design instead of a 3 peice. It does not say Cyclone on the casting. This manifold is found in EDM Galant Dynamic-4, Galant AMG, JDM/EDM Galant GTi. They are rare items and also have actuated butterflies and split runners. These intake manifolds have a far smoother design with better shaped runners and a larger plenum volume. The top end powerband is a good bit better then the Turbo Cyclone but not much. This manifold is good for about 8000-9000 RPM or higher depending on camshaft.
 +{{ http://w4a33.com/images/ntcyclone.jpg?467x350 }}
 ===JMF Race=== ===JMF Race===
 The JMF "RACE" version intake manifold is for the daily driven weekend race warriors who want the best of both worlds, more HP without sacrificing a lot of spool and streetability.  With over 10 years of proven results, our budget friendly "RACE" version intake manifold is the best bang for you buck.  Our latest revision introduces a CNC machined billet runner section that bolts to the plenum for modular functionality.  Expected gains can be anywhere from 10-45 HP based on your setup and tuning. This manifold is good for about 8500-9000 RPM or higher depending on camshaft. The JMF "RACE" version intake manifold is for the daily driven weekend race warriors who want the best of both worlds, more HP without sacrificing a lot of spool and streetability.  With over 10 years of proven results, our budget friendly "RACE" version intake manifold is the best bang for you buck.  Our latest revision introduces a CNC machined billet runner section that bolts to the plenum for modular functionality.  Expected gains can be anywhere from 10-45 HP based on your setup and tuning. This manifold is good for about 8500-9000 RPM or higher depending on camshaft.
 +{{ http://w4a33.com/images/jmfrace.jpg?467x350 }}
  
 ===Magnus V3=== ===Magnus V3===
Line 39: Line 42:
  
 With that being the case, the intake manifold needs to be optimized to feed these flow-hungry ports. Using advanced computer modeling techniques and after 7 iterations, we finally achieved the design we were looking for. From 20 PSI to 100 PSI. and from 40 lbs of airflow to 160lbs of airflow, the new 1G V3 cast manifold has equal flow distribution within 1 percent in each cylinder. That’s something none of the competition can even approach. In addition to unmatched flow distribution, the 1G V3 manifold offers reduced restriction and increased flow compared to all our previous designs. With that being the case, the intake manifold needs to be optimized to feed these flow-hungry ports. Using advanced computer modeling techniques and after 7 iterations, we finally achieved the design we were looking for. From 20 PSI to 100 PSI. and from 40 lbs of airflow to 160lbs of airflow, the new 1G V3 cast manifold has equal flow distribution within 1 percent in each cylinder. That’s something none of the competition can even approach. In addition to unmatched flow distribution, the 1G V3 manifold offers reduced restriction and increased flow compared to all our previous designs.
 +{{ http://w4a33.com/images/magnus.jpg?467x350 }}
  
 ===JMF Drag=== ===JMF Drag===
  The JMF "DRAG" version intake manifold is for the hard core racers putting down serious power.  If you need one of the highest flowing 4G63 intake manifolds available look no further.  Over a year in the making, our DRAG manifold went through a complete overhaul.  No corners were cut when it came to the design and functionality of this manifold.  Every component on this manifold is CNC machined from billet aluminum, not a single weld is present.  Extensive flow testing was conducted on several prototypes until we found the perfect design with the best balance possible. This manifold is good for about 9000 RPM or higher depending on camshaft.  The JMF "DRAG" version intake manifold is for the hard core racers putting down serious power.  If you need one of the highest flowing 4G63 intake manifolds available look no further.  Over a year in the making, our DRAG manifold went through a complete overhaul.  No corners were cut when it came to the design and functionality of this manifold.  Every component on this manifold is CNC machined from billet aluminum, not a single weld is present.  Extensive flow testing was conducted on several prototypes until we found the perfect design with the best balance possible. This manifold is good for about 9000 RPM or higher depending on camshaft.
 +{{ http://w4a33.com/images/jmfdrag.jpg?467x350 }}
  
 ==== Small Runner ==== ==== Small Runner ====
Line 48: Line 52:
 {{http://w4a33.com/images/stk2ginmni.jpg?263x200 }} {{http://w4a33.com/images/stk2ginmni.jpg?263x200 }}
 This manifold works very well and its bottom and mid range powerband are very difficult to beat. However this manifold lacks in top end performance. This manifold can be used on any combination but most of the other intake manifolds listed here will produce decent gains on the top end over the stock manifold. This manifold is good for about 6000-7500 RPM or higher depending on camshaft. This manifold works very well and its bottom and mid range powerband are very difficult to beat. However this manifold lacks in top end performance. This manifold can be used on any combination but most of the other intake manifolds listed here will produce decent gains on the top end over the stock manifold. This manifold is good for about 6000-7500 RPM or higher depending on camshaft.
-===Evo3===+===Evo3/RVR===
 {{ http://w4a33.com/images/evo3inmni.jpg?267x200}} {{ http://w4a33.com/images/evo3inmni.jpg?267x200}}
-The Evo3 intake has a bigger plenum and shorter runners than a 2g intake. This will allow it to make power higher up in the rpm band. It's a nice compromise between the 6500rpm cuttoff of a stocker +The Evo3 intake has a bigger plenum and shorter runners than a 2g intake. This will allow it to make power higher up in the rpm band. It's a nice compromise between the 6500rpm cuttoff of a stocker. RVR Runner’s and plenum are the same. RVR has smaller TB inlet, it doesn’t have the port for the egr (wasn’t used for that tho), RVR also is just missing a couple extra vacuum nipples. 
-===JMF Street===+===JMF Race===
 The JMF "RACE" version intake manifold is for the daily driven weekend race warriors who want the best of both worlds, more HP without sacrificing a lot of spool and streetability.  With over 10 years of proven results, our budget friendly "RACE" version intake manifold is the best bang for you buck.  Our latest revision introduces a CNC machined billet runner section that bolts to the plenum for modular functionality.  Expected gains can be anywhere from 10-45 HP based on your setup and tuning. This manifold is good for about 8500-9000 RPM or higher depending on camshaft. The JMF "RACE" version intake manifold is for the daily driven weekend race warriors who want the best of both worlds, more HP without sacrificing a lot of spool and streetability.  With over 10 years of proven results, our budget friendly "RACE" version intake manifold is the best bang for you buck.  Our latest revision introduces a CNC machined billet runner section that bolts to the plenum for modular functionality.  Expected gains can be anywhere from 10-45 HP based on your setup and tuning. This manifold is good for about 8500-9000 RPM or higher depending on camshaft.
 +{{ http://w4a33.com/images/jmfrace.jpg?467x350 }}
 ===Magnus V4=== ===Magnus V4===
 After endless hours dedicated to creating prototypes, testing and perfecting we had reached the results that we were looking for. The result that we had achieved from the last prototype was up to our standards, was Magnus approved and that is when the V4 cast manifold was born. We dedicated almost two years of research and development using enhanced flow dynamics utilizing CAD Modeling & CFD simulation to develop the manifold. It’s made from A356-T6 aluminum alloy and can be installed in stock location with clearance for the original battery. The Manifold can be configured for 8 injectors using the Magnus weld in dual fuel rail kit and fits factory fuel rail or Magnus high flow fuel rail. Featuring 5L plenum with contoured velocity stacks molded into the floor for huge top end and minimal turbulence. This manifold is good for about 9000 RPM or higher depending on camshaft. After endless hours dedicated to creating prototypes, testing and perfecting we had reached the results that we were looking for. The result that we had achieved from the last prototype was up to our standards, was Magnus approved and that is when the V4 cast manifold was born. We dedicated almost two years of research and development using enhanced flow dynamics utilizing CAD Modeling & CFD simulation to develop the manifold. It’s made from A356-T6 aluminum alloy and can be installed in stock location with clearance for the original battery. The Manifold can be configured for 8 injectors using the Magnus weld in dual fuel rail kit and fits factory fuel rail or Magnus high flow fuel rail. Featuring 5L plenum with contoured velocity stacks molded into the floor for huge top end and minimal turbulence. This manifold is good for about 9000 RPM or higher depending on camshaft.
 +{{ http://w4a33.com/images/magnus.jpg?467x350 }}
 ===JMF Drag=== ===JMF Drag===
  The JMF "DRAG" version intake manifold is for the hard core racers putting down serious power.  If you need one of the highest flowing 4G63 intake manifolds available look no further.  Over a year in the making, our DRAG manifold went through a complete overhaul.  No corners were cut when it came to the design and functionality of this manifold.  Every component on this manifold is CNC machined from billet aluminum, not a single weld is present.  Extensive flow testing was conducted on several prototypes until we found the perfect design with the best balance possible. This manifold is good for about 9000 RPM or higher depending on camshaft.  The JMF "DRAG" version intake manifold is for the hard core racers putting down serious power.  If you need one of the highest flowing 4G63 intake manifolds available look no further.  Over a year in the making, our DRAG manifold went through a complete overhaul.  No corners were cut when it came to the design and functionality of this manifold.  Every component on this manifold is CNC machined from billet aluminum, not a single weld is present.  Extensive flow testing was conducted on several prototypes until we found the perfect design with the best balance possible. This manifold is good for about 9000 RPM or higher depending on camshaft.
 +{{ http://w4a33.com/images/jmfdrag.jpg?467x350 }}
  
 ==== Intake Manifolds to avoid ==== ==== Intake Manifolds to avoid ====
 Venom and Slowboy Racing Sheet metal intake manifolds are for some reason sought after. Both of these intakes are very terrible. I have back to back compared them with stock and the stock intake manifold picked up quite a but of midrange power and spool over them. Do not use these. They are seriously junk with no R&D. They are also known to crack and burst.  Venom and Slowboy Racing Sheet metal intake manifolds are for some reason sought after. Both of these intakes are very terrible. I have back to back compared them with stock and the stock intake manifold picked up quite a but of midrange power and spool over them. Do not use these. They are seriously junk with no R&D. They are also known to crack and burst. 
intakemanifold.1589619160.txt.gz · Last modified: 2020/05/16 08:52 by admin