|
|
 06-13-2001, 06:52 PM |
#1 |
|
DSMtalker
|
Hey guys, can the cyclone intake
manifold be put on a car with a/c? The manifold i am talking about is the
one from the 240hp car that dont say cyclone
on it but is still a dual runner design. I've been told it hits the a/c pump,
is there anyway I can get this thing installed without having to get rid
of my a/c? Also to have the butterflies properly controlled do i need a
jdm ecu??
__________________ 91 TSI AWD 13.4@100 on pump gas |
  |
  |
| 06-14-2001, 01:29 AM |
#2 |
|
New DSMtalker
|
cyclone intake manifold
Im pretty sure the manifold wont hit the ac compressor. extreme turbo
said that all you had to do was switch ac compressor mounts from the stock
motor to the cyclone motor if it hits. My
friends and i did a cyclone swap a couple of
weeks ago, but we didnt put the ac compressor back in..... about the ecu
im not sure if the jdm opens the second butterflies, but it was a big
power difference (better) compared to the stock ecu. |
| |
|
| 06-14-2001, 12:47 PM |
#3 |
|
Hardcore DSMtalker
2006 Scoobie WRX Wagon Join Date: Oct 2000
Location: Lititz, PA, USA
Posts: 696 Trader Rating: (0)
Lipster's Photo Gallery
|
On my car, the mounts for the A/C had to be reworked (extended) and
the manifold was ground down a little bit so it could fit in.
I THINK there were butterflies controlled by the ECU, but I know mine is via vacuum. On the driver side of the intake, is there a vacuum valve ? __________________ '93 Laser AWD - RIP '02 Grand Am GT - RIP 2004 WRX Wagon - TRADE 2006 WRB WRX Wagon - They finally got it right |
| |
|
| 06-14-2007, 05:45 AM |
#4 |
|
New DSMtalker
 1991 Eagle Talon TSI Join Date: Jun 2007
Location: Colorado, U.S.A.
Posts: 10 Trader Rating: (0)
maxpsistop's Photo Gallery
|
Re: Cyclone Intake HELP!
I installed a cyclone on my 1st gen and
it does not hit the a/c compressor. The only problem you have to deal with
is all of the vac lines for the evap emissions control system on the
bracket, they are not able to fit and flow up through the same path, you
have to redo the lines in a different fashion out of the way cause the
manifold bracket does not allow for enough
space |
| |
|
| 06-14-2007, 11:13 AM |
#5 |
|
Super DSMtalker
97 Eagle Talon TSI AWD Join Date: Aug 2003
Location: Gilbert, AZ
Posts: 303 Trader Rating: (0)
Stormbird's Photo Gallery
|
Re: Cyclone Intake HELP!
DSMchips.com (keydiver) has a chip modification that will run the
cyclone for
you. |
| |
|
| 06-14-2007, 10:26 PM |
#6 |
|
Elite DSMtalker
 2005 Evolution VIII RS Join Date: Aug 2002
Location: Pittsburgh
Posts: 2,101 Trader Rating: (7)
Asmodeus's Photo Gallery
|
Re: Cyclone Intake HELP!
DSMlink's nitrous control's also work pretty damn good.
 I have one too. No AC tho. What parameters does dsmchips use to drive the cyclone? (just curious) __________________ -Dustin Demon Motor Works 1995 Talon TSi AWD Evo III 16G- 2005 Evolution RS 3076R- |
| |
|
 |
| vBulletin Message | |
| Cancel Changes | |
| Currently Active Users Viewing This Thread: 1 (1 members and 0 guests) | |
| Flying Eagle |
| Display Modes |
Linear Mode |
Switch
to Hybrid Mode |
Switch
to Threaded Mode |
|
|
